WinTV-Radio: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
m (Category)
No edit summary
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
{{Note|I'm not aware of the exact name under which this card was sold. I'm just guessing that is WinTV-Radio. If someone knows better, please feel free to move this page and giving it a proper name.}}<br />

[[Image:Wintv-radio-C121.jpg|200px|thumb|WinTV 44914 Rev C121]]
[[Image:Wintv-radio-C121.jpg|200px|thumb|WinTV 44914 Rev C121]]
[[Image:Wintv-radio-c121-connectors.jpg|200px|thumb|WinTV 44914 Rev C121 - Connectors]]
[[Image:Wintv-radio-c121-connectors.jpg|200px|thumb|WinTV 44914 Rev C121 - Connectors]]
Line 16: Line 18:


It may be necessary to load bttv module with parameter automute=0 if audio is unwantedly muting.
It may be necessary to load bttv module with parameter automute=0 if audio is unwantedly muting.


Remote is fully supported by lirc. With v4l-dvb drivers some known changes would need to be done to get the remote working.

Following modification was not accepted by maintainer (change was requested) but it may be applied to source code and recompiled to get this remote to a working state with v4l-dvb drivers.

http://www.spinics.net/lists/linux-media/msg15496.html


===Sample dmesg output===
===Sample dmesg output===

Latest revision as of 11:37, 5 February 2010

Note: I'm not aware of the exact name under which this card was sold. I'm just guessing that is WinTV-Radio. If someone knows better, please feel free to move this page and giving it a proper name.


WinTV 44914 Rev C121
WinTV 44914 Rev C121 - Connectors
WinTV 44914 Rev C121 - Remote

WinTV Model 44914 Rev C121

An analog PCI card from Hauppauge.

Connectors

Radio In, TV In, Line Out, Composite In, Line In, IR In.

Support

Everything is working "out of the box" except bundled remote control.

It may be necessary to load bttv module with parameter automute=0 if audio is unwantedly muting.


Remote is fully supported by lirc. With v4l-dvb drivers some known changes would need to be done to get the remote working.

Following modification was not accepted by maintainer (change was requested) but it may be applied to source code and recompiled to get this remote to a working state with v4l-dvb drivers.

http://www.spinics.net/lists/linux-media/msg15496.html

Sample dmesg output

bttv: driver version 0.9.18 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 18, latency: 32, mmio: 0xdfdfe000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
IRQ 18/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 1-0050: Hauppauge model 44914, rev C121, serial# 3959906
tveeprom 1-0050: tuner model is Philips FM1216 (idx 21, type 5)
tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 1-0050: audio processor is None (idx 0)
tveeprom 1-0050: has radio
bttv0: Hauppauge eeprom indicates model#44914
bttv0: tuner type=5
bttv0: audio absent, no audio device found!
tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner-simple 1-0061: creating new instance
tuner-simple 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 . ok