Pinnacle PCTV Pro: Difference between revisions
Jump to navigation
Jump to search
m (fixed link ... again :() |
m (remove link to deleted article) |
||
| Line 7: | Line 7: | ||
See also: |
See also: |
||
*[[CARDLIST.bttv]] |
|||
*[[Bttv devices (bt848, bt878)]] |
*[[Bttv devices (bt848, bt878)]] |
||
Revision as of 03:28, 27 August 2007
- Miro PCTV
- Miro PCTV Pro
- Pinnacle PCTV
- Pinnacle PCTV Pro
These Miro and Pinnacle cards were the original PCTV series, produced from December 1997 onwareds. They are based on the Bt848 chip. The PCTV Pro includes an FM radio chip.
See also:
Pro model with FM plug-in card.
TODO
- Sound: Needs to be redirected using sox.
- Remote control, needs some configuration, and maybe lirc? See also Remote controllers
Remote control
The Pinnacle cards are supplied with a remote controller which seems to be the same as for Pinnacle PCTV 50i
Card features
- PCI
- PAL/NTSC/SECAM
- Video/audio decoder: bt848
- Analog demodulator: MSP3410D-B4 (msp3400)
- TV tuner: Temic 4002 FH5 (also possibly Philips on some cards)
- FM radio chip (PRO only): MSP3410
- Supports 16:9-format (?)
- Resolution: 768x576 and 720x576 (PAL)
The card has no on board sound AD nor remote control input.
Card connectors
- TV RF signal: ??? with adapter to IEC connector (PAL)
- Video Input: S-Video
- Video Input: Composite Video (RCA socket)
- Audio Outputs: 3.5 mm jack
- FM radio RF signal (PRO only): Internal RC jack with flying wire to IEC connector
- Video composite out (internal)
Connecting the card
- The TV antenna signal is connected to the antenna input.
- A cable (supplied) should be connected from the card audio output connector to a generic sound input (usually found on the main board).
- The remote control sensor cable (supplied) is connected to a 9 pin serial input (usually there is one on the main board).
lspci -v
00:0a.0 Multimedia video controller: Brooktree Corporation Bt848 Video Capture (rev 12)
Flags: bus master, medium devsel, latency 32, IRQ 21
Memory at e2001000 (32-bit, prefetchable) [size=4K]
Module Options
The cards may be detected automatically, but at least for the Pro card is is required to specify options explicitly in /etc/modules.cond (for Fedora, other distributions may do it differently):
options bttv card=11 tuner=0
Kernel output
bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt848 (rev 18) at 0000:00:0a.0, irq: 21, latency: 32, mmio: 0xe2001000 bttv0: using: MIRO PCTV pro [card=11,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00e707df [init] tuner 2-0060: All bytes are equal. It is not a TEA5767 tuner 2-0060: chip found @ 0xc0 (bt848 #0 [sw]) tuner 2-0061: chip found @ 0xc2 (bt848 #0 [sw]) msp3400 2-0040: MSP3410D-B4 found @ 0x80 (bt848 #0 [sw]) msp3400 2-0040: MSP3410D-B4 supports nicam, mode is autodetect bttv0: i2c: checking for MSP34xx @ 0x80... found bttv0: miro: id=1 tuner=0 radio=matchbox stereo=yes bttv0: using tuner=0 tuner 2-0060: type set to 0 (Temic PAL (4002 FH5)) bttv0: i2c: checking for MSP34xx @ 0x80... found bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found bttv0: i2c: checking for TDA9887 @ 0x86... not found bttv0: registered device video1 bttv0: registered device vbi1 bttv0: registered device radio1