Pinnacle PCTV HD Card (800i)

Pinnacle PCTV HD Card (800i)

A hybrid ATSC PCI card from Pinnacle.

It is supported under Linux, but drivers are currently available for it only from LinuxTV (see below for driver detail). Inclusion of support into the kernel will likely occur for 2.6.25.

Overview/Features

A hybrid device that supports analog, ATSC (8-VSB) and digital cable (QAM) TV sources. The card also supports analog A/V inputs, and has an IR remote control input.

It appears that it may be also being sold as the Yuan PG583Q. Yuan lists two models (PG583 and PG583Q) -- simply a wild guess, but perhaps the former uses a XC3028 (not QAM capable) and the later XC5000 (QAM capable) ?? The Yuan boards also have a connector of sorts on the back portion of the PCB that is not present on the Pinnacle board.

Components Used

800i's components

• Xceive XC5000 (tuner & analog IF demodulator) [1]
• Samsung S5H1409 (digital demodulator) [2]
• Conexant CX23883 (A/V decoder & PCI bridge) [3]
• Cirrus 5340 CZZ (audio ADC) [4]
• Atmel ATMLH726 (8-pin eeprom)

Identification

PCI subsytem ID is: 11bd:0051

Output of lspci -vvnn:

00:0a.0 Multimedia video controller [0400]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
	Subsystem: Pinnacle Systems Inc. Unknown device [11bd:0051]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.1 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8801] (rev 05)
	Subsystem: Pinnacle Systems Inc. Unknown device [11bd:0051]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.2 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)
	Subsystem: Pinnacle Systems Inc. Unknown device [11bd:0051]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Making it Work

Firmware

You must have the firmware for the XC5000 tuner installed for the 800i to function properly. It is available at [5] together with the extracting script.

Drivers

Full support for the device is now in the mainline v4l-dvb repo. Both analog and digital TV are supported, and the remote control should also function properly now.

To download the latest v4l-dvb tree, simply select the bz2 or gz link on the top left of the page, then build them via running "make" followed by "make install". More thorough downloading/building instructions can be found here.

Sample kernel output

insert relevant portion of dmesg output here

Remote Control Support

The card uses the CX2388x's standard IR interface, and, it is fully supported now via the linux input layer. You may use LIRC with the input device driver option. See the Remote Controllers page for more details on how to configure LIRC with remote controls that use the linux input layer.

External Links

• Pinnacle product page