Hauppauge WinTV-NOVA-T-Stick: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
(switching to Making it work dib0700 template)
(put back specific lircd.conf)
Line 72: Line 72:


{{Making-it-work:dvb-usb-dib0700}}
{{Making-it-work:dvb-usb-dib0700}}

Here is a proper <tt>lircd.conf</tt>:

#
# brand: Hauppauge
# model no. of remote control: 45 buttons Snowboard Shape Silver over Black
#
begin remote
name hauppauge-45-snowboard
bits 16
eps 30
aeps 100
one 0 0
zero 0 0
pre_data_bits 16
pre_data 0x1
gap 199999
toggle_bit 0
begin codes
Go 0x0162
Power 0x0074
TV 0x0179
Videos 0x0189
Music 0x0188
Pictures 0x00E2
Guide 0x016D
Radio 0x0181
ArrowUp 0x0067
ArrowLeft 0x0069
OK 0x0160
ArrowRight 0x006A
ArrowDown 0x006C
BackExit 0x009E
Menu 0x008B
VolumeUp 0x0073
VolumeDown 0x0072
PrevCh 0x016B
Mute 0x0071
ChannelUp 0x0192
ChannelDown 0x0193
Record 0x00A7
Rewind 0x00A8
SkipBack 0x0195
Play 0x00CF
Pause 0x0077
Stop 0x0080
Fwdwind 0x00D0
SkipFwd 0x0197
1 0x0002
2 0x0003
3 0x0004
4 0x0005
5 0x0006
6 0x0007
7 0x0008
8 0x0009
9 0x000A
* 0x0037
0 0x000B
# 0x0029
Red 0x018E
Green 0x018F
Yellow 0x0190
Blue 0x0191
end codes
end remote





Revision as of 14:01, 20 February 2008

WinTV-Nova-T-Stick

A DVB-T USB device from Hauppauge.

It is supported under Linux.

Note: Currently, the Nova-T Stick (70009) is known to suffer from I2C errors. Updating to current Hg drivers and using new firmware should cure this.


Overview/Features

  • IR receiver
  • Remote control A415-HPG-WE-A (grey top, black bottom, 45 buttons, snowboard shape) with models: 1157 G (Spain)

Components Used

  • Microtune MT2060 tuner
  • Dibcom DiB7700 DVB-T demodulator & USB 2.0 controller

Identification

USB ID Model no. Version Tuner Supported from
Device Box
2040:7050 70001 Model 294 SL-294-V2.0-UK DiB7700M 2.6.19
2040:7060 70009 Model 1132 DiB7700P 2.6.20
Model 308
Model 99063-001
("lite" version)
2040:7070 ?? Model 294 G (Sold in Germany as Nova-T-lite) SL-294-V2.3-UK DiB7070P v4l-dvb repository, 25 January 2008
(Nova-T-CE)
Model 1157 G SL-1157-V2.2-SP
Nova-T-SE Model 1166 G v4l-dvb repository, 2 February 2008
  • One model number is above the MAC address on the label on the underside of the device.
Note: Model 1157 G (USB ID 2040:7070) doesn't have this model number (device number?) above the MAC address, It has a 2D code instead.
  • The other model number and the version information are on the base of the box, below the bar code.
Note: see Peter's Aug 9/2007 note regarding boxes and this list of model numbers, both on the discussion page.


Making it Work (generic for all dib0700)

Firmware

August 21, 2008 - New firmware file fixing the last cause for i2c errors and disconnects and providing a new, more modular i2c request formatting.

You will need the dvb-usb-dib0700-1.20.fw firmware file in /lib/firmware or the relevant place for your distribution.

You may need to change the name of the file to dvb-usb-dib0700-1.10.fw or create a link until the driver code reflects that change.

For archival purposes: dvb-usb-dib0700-1.10.fw firmware file

August 29,2008 - Issues with Firmware 1.20. Some issues have been found with the latest version of the firmware. Users may wish to continue to use 1.10 unless they have patched their v4l-dvb code with dib0700_new_i2c_api.patch.

November 15,2008 - Issues with Firmware 1.20.

  • The above mentioned dib0700_new_12c_api.patch is not available discretely but is now rolled into the mercurial drivers
  • dvb-usb-dib0700-1.20.fw firmware file is now stable for reception, but remote control functionality is broken; any key press is repeated until the next key is pressed. The only way to get remote control functionality presently is to roll back to 1.10 firmware and suffer the occasional disconnect.
  • The mercurial drivers have been changed so they now load 1.20 firmware. To revert to 1.10 firmware you need to rename your firmware file to dvb-usb-dib0700-1.20.fw or provide a link of that name.
  • To avoid spurious remote control signals with 1.20 firmware, you need to edit /etc/modprobe.d/options or from Ubuntu onwards /etc/modprobe.d/options.confand add:
options dvb_usb disable-rc-polling=1

November 28,2008 - i2c errors. Changes were made to the remote control drivers on November 16,2008 to correct the repeat key problem. The card is generally stable for dual tuner reception and remote control function with Firmware 1.20.

November 10,2009 - mt2060 I2C write failed. Possible regression of a driver bug raised against Ubuntu running 2.6.27-14 and 2.6.31-2.17 causing mt2060 I2C errors in MythTV useage with firmware 1.20. https://bugs.launchpad.net/ubuntu/+source/linux/+bug/397696 Recommend check the kernel extensions listed here for Low Noise Activation and rc_polling are loaded with correct config file name for your distribution, EIT listings information is turned off until a suitable delay (500ms-1000ms)is added to a single card (not both) and the card has correctly been added to the database as two tuners (no additional NULL entries) in the mythtv recordcard table.

Drivers

It requires the dib0700 driver. Just use Mercurial by following the How to Obtain, Build and Install V4L-DVB Device Drivers instructions.

Forcing the activation of LNAs (Low Noise Amplifier)

You may have to force LNA to get this card working:

In /etc/modprobe.d/options add:

options dvb_usb_dib0700 force_lna_activation=1

Disabling the remote control sensor

You may want to disable the remote control sensor if you are using another one and want to avoid error messages in the logs:

In /etc/modprobe.d/options add:

options dvb_usb disable_rc_polling=1

All relevant kernel modules options

In /etc/modprobe.d/options add:

options [module name] [option name]=[setting]

Get the parameters list using

modinfo [name of kernel module]

The debug values are bit fields, with each bit representing a different category. Add values to turn on multiple debugging categories.

dib3000mc
debug
Turn on debugging
Values: integer
Default: 0 (off)
buggy_sfn_workaround
Enable work-around for buggy SFNs
Values: integer
Default: 0 (disabled)
mt2060
debug
Turn on debugging
Values: integer
Default: 0 (off)
dvb_usb_dib0700
force_lna_activation
Force the activation of LNAs (Low Noise Amplifier), if applicable for the device
Values: integer
Default: 0 (automatic/off)
dvb_usb_dib0700_ir_proto
Set IR protocol
Values: integer 0=NEC, 1=RC5, 2=RC6
Default: 1
debug
Set debugging level
Values: integer (bitmap) 1=info, 2=fw, 4=fwdata, 8=data
Default: 0 (none)
dvb_usb
debug
Set debugging level
Values: integer (bitmap) 1=info, 2=xfer, 4=pll, 8=ts, 16=err, 32=rc, 64=fw, 128=mem, 256=uxfer
Default: 0 (none)
disable_rc_polling
Disable remote control polling
Values: integer
Default: 0 (enabled)
force_pid_filter_usage
Force all DVB USB devices to use a PID filter, if any
Values: integer
Default: 0 (disabled)
dvb_core
dvb_net_debug
Enable debug messages
Values: integer
Default: 0 (disabled)
frontend_debug
Turn on frontend core debugging
Values: integer
Default: 0 (off)
dvb_shutdown_timeout
Wait n seconds after close() before suspending hardware
Values: integer
Default: 0
dvb_force_auto_inversion
Set whether INVERSION_AUTO is forced on
Values: integer
Default: 0 (off)
dvb_override_tune_delay
Wait n milliseconds for lock after a tuning attempt
Values: integer
Default: 0
dvb_powerdown_on_sleep
Turn LNB power off on sleep
Values: integer
Default: 1 (enabled)
cam_debug
Enable verbose debug messages
Values: integer
Default: 0 (off)
debug
Turn on debugging
Values: integer
Default: 0
dvbdev_debug
Turn on device debugging
Values: integer
Default: 0 (off)
dibx000_common
debug
Turn on debugging
Values: integer
Default: 0 (off)

Remote control support

Using evdev

As long as the evdev module is loaded, a remote that is recogniced as hid device will be treated as a usb keyboard and this means that you can avoid using lirc.

However, many of the keys on your remote may generate keycodes which are not mapped to anything, by default.

In X you can use xev to find the keycodes and xmodmap to map them to useful symbols. Unfortunately, some keys may generate keycodes that X doesn't recognize at all and the device does not support keymaps, or this would be easy to fix.

Using LIRC

Usually remote controls in linux are managed by the lirc software collection.

To get lirc up and running you need to configure some things.

  • Settings for the hardware
    • Where does lirc get its input from? aka. the DEVICE. E.g. /dev/input/event3
    • How to handle the input? aka. the DRIVER. E.g. devinput
  • Settings for mapping driver output generated by your remote (a bunch of hex numbers) to key names (something like 0..9, Volume+, Next, Record)
  • Settings for mapping key presses to actions (usually located in your .lircrc)
Mythubuntu case

On mythubuntu 10.10, you just have to add this line in /etc/udev/rules.d/65-persistent-hauppauge.rules

SUBSYSTEM=="input", KERNEL=="event*", ATTRS{idVendor}=="2040", ATTRS{idProduct}=="8400", SYMLINK+="lirc0"
Device/driver settings

Find the IR receiver's device by looking in the dmesg output for a line similar to:

input: IR-receiver inside an USB DVB receiver as /class/input/input4

Additionally, the IR receiver will be listed if you execute the command:

cat /proc/bus/input/devices

For example:

I: Bus=0003 Vendor=2040 Product=9950 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:07:01.2-1/ir0
S: Sysfs=/class/input/input4
U: Uniq=
H: Handlers=kbd event4 
B: EV=3
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffd

In this example, the remote control gives output into /dev/input/event4.

The event number depends on your particular system and can vary.

Eventually this event number can even vary at every reboot.

You could create a new udev rule in /etc/udev/rules.d/65-persistent-hauppauge.rules.

KERNEL=="event*", ATTRS{name}=="IR-receiver inside an USB DVB receiver", SYMLINK+="input/dvb-ir"

This would make IR receivers handled by the usb_dvb framework always always be linked to /dev/input/dvb-ir.

But Linux systems running recent udev will automatically create non-varying names, a nicer and automatic way of providing a stable input event name:

$ ls -la /dev/input/by-path/
total 0
drwxr-xr-x 2 root root 140 2008-02-07 20:31 .
drwxr-xr-x 4 root root 280 2008-02-07 20:31 ..
lrwxrwxrwx 1 root root   9 2008-02-07 20:31 pci-0000:00:1a.1-usb-0:2:1.0-event-kbd -> ../event1
lrwxrwxrwx 1 root root   9 2008-02-07 20:31 pci-0000:00:1a.1-usb-0:2:1.1-event-mouse -> ../event2
lrwxrwxrwx 1 root root   9 2008-02-07 20:31 pci-0000:00:1a.1-usb-0:2:1.1-mouse -> ../mouse1
lrwxrwxrwx 1 root root   9 2008-02-07 20:31 pci-4-1--event-ir -> ../event4
lrwxrwxrwx 1 root root   9 2008-02-07 20:31 platform-pcspkr-event-spkr -> ../event3

LIRC will use it without needing a special kernel module. use the dev/input (or devinput. Check this with the command "lircd --device=help".) driver and specify the input event device in /etc/lirc/hardware.conf

# /etc/lirc/hardware.conf
#
# Arguments which will be used when launching lircd
LIRCD_ARGS=""

#Don't start lircmd even if there seems to be a good config file
#START_LIRCMD=false

#Try to load appropriate kernel modules
LOAD_MODULES=true

# Run "lircd --driver=help" for a list of supported drivers.
DRIVER="dev/input"
# If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0 will be
# automatically used instead
REMOTE_DEVICE="/dev/input/by-path/pci-4-1--event-ir"
MODULES=""

# Default configuration files for your hardware if any
LIRCD_CONF="/etc/lirc/lircd.conf"
LIRCMD_CONF=""

If you have REMOTE and TRANSMITTER sections in your hardware.conf file, they should look like this:

#Chosen Remote Control
REMOTE="Terratec Cinergy DT USB XS Diversity"
REMOTE_MODULES=""
REMOTE_DRIVER="devinput"
REMOTE_DEVICE="/dev/input/by-path/pci-1-5-event-ir"
REMOTE_LIRCD_CONF="/etc/lirc/lircd.conf"
REMOTE_LIRCD_ARGS=""
#Chosen IR Transmitter
TRANSMITTER="None"
TRANSMITTER_MODULES=""
TRANSMITTER_DRIVER=""
TRANSMITTER_DEVICE=""
TRANSMITTER_LIRCD_CONF=""
TRANSMITTER_LIRCD_ARGS=""
Remote key setup

See device specific section below or try [1].


Sample .lircrc

A sample .lircrc can be found LircrcExample here.

Keys repeated twice

But there is still the problem of the key repeats for it, so that each keypress will be repeated twice. The patches, as mentioned above, may not work, but a workaround is possilbe. It is described in http://ubuntuforums.org/showthread.php?p=4253678

Simply add config = echo " > /dev/null before the main config in .mythtv/lircrc or .lircrc

 begin
  prog = mythtv
  button = Mute
  config = echo " > /dev/null
  config = |
  ...
 end

So each 2nd keypress will be suppressed. This works in some application but not others (e.g. vlc).

Alternatively there is a patch for the kernel driver that solves it, it can be found here.

Finally if that doesn't work and you have the silver remote (A415-HPG-WE-A ) then changing the lircd.conf line as follows can prevent the duplicate key presses. This has the side-effect of disabling key repeats for the remote entirely. Change toggle_bit_mask 0x80000000 to toggle_bit_mask 0x00000000

Note: do not try to comment out (using #) any line in this file, or lirc won't work anymore.

Do NOT do this:

 #toggle_bit_mask 0x80000000
 toggle_bit_mask 0x00000000

Replace the original line instead.

Here is a proper lircd.conf:

#
# brand:                       Hauppauge
# model no. of remote control: 45 buttons Snowboard Shape Silver over Black
#

begin remote

 name  hauppauge-45-snowboard
 bits           16
 eps            30
 aeps          100

 one             0     0
 zero            0     0
 pre_data_bits   16
 pre_data       0x1
 gap          199999
 toggle_bit      0


     begin codes
         Go                       0x0162
         Power                    0x0074
         TV                       0x0179
         Videos                   0x0189
         Music                    0x0188
         Pictures                 0x00E2
         Guide                    0x016D
         Radio                    0x0181
         ArrowUp                  0x0067
         ArrowLeft                0x0069
         OK                       0x0160
         ArrowRight               0x006A
         ArrowDown                0x006C
         BackExit                 0x009E
         Menu                     0x008B
         VolumeUp                 0x0073
         VolumeDown               0x0072
         PrevCh                   0x016B
         Mute                     0x0071
         ChannelUp                0x0192
         ChannelDown              0x0193
         Record                   0x00A7
         Rewind                   0x00A8
         SkipBack                 0x0195
         Play                     0x00CF
         Pause                    0x0077
         Stop                     0x0080
         Fwdwind                  0x00D0
         SkipFwd                  0x0197
         1                        0x0002
         2                        0x0003
         3                        0x0004
         4                        0x0005
         5                        0x0006
         6                        0x0007
         7                        0x0008
         8                        0x0009
         9                        0x000A
         *                        0x0037
         0                        0x000B
         #                        0x0029
         Red                      0x018E
         Green                    0x018F
         Yellow                   0x0190
         Blue                     0x0191
     end codes

end remote


Specific to the model

Supported in v4l-dvb as of 18 August 2007. The 70001 version has an IR sensor, and the 70009 version is listed by Wikipedia as having one. It works with Hauppauge's 45-button remote control and will handle signals from similar remote controls.


Sample kernel output

This is for the 70001 version, using the driver in Linux 2.6.22.1.

usb 1-10: new high speed USB device using ehci_hcd and address 8
usb 1-10: configuration #1 chosen from 1 choice
dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Hauppauge Nova-T Stick).
DVB: registering frontend 2 (DiBcom 7000MA/MB/PA/PB/MC)...
MT2060: successfully identified (IF1 = 1220)
dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.

This is for the model 294 G, using the driver in Linux 2.6.23.9 with a HG of v4l-dvb from 29th of December 2007.

usb 3-5: new high speed USB device using ehci_hcd and address 80
usb 3-5: configuration #1 chosen from 1 choice
dib0700: loaded with support for 5 different device-types
dvb-usb: found a 'DiBcom STK7070P reference design' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'DiBcom STK7070P reference design' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (DiBcom STK7070P reference design)
DVB: registering frontend 0 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: DiBcom STK7070P reference design successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_dib0700


External Links