Hauppauge WinTV-NOVA-T-500
This is a dual tuner DVB-T PCI card from Hauppauge. In actuality, the receivers are USB devices, but there aren't any USB plugs or sockets involved -- the single PCI card itself sports on board dual USB based receivers that interface with a host USB 2.0 controller. This unique design is also known as "Bristol".
As it requires the dib0700 driver, native support for this card requires Linux 2.6.19 or higher.
Component Overview
- 2x Microtune MT2060 tuner
- 2x DiB3000P Dibcomm DVB-T demodulator & USB controller
- 1x VIA VT8xxx host USB 2.0 controller (USB-to-PCI)
- A single Low Noise Amplifier (LNA) is present for both channels, but needs to be manually activated (see below).
Some further technical details may be found in DiBcom USB2.0 DVB-T devices (based on the DiB0700)
You will find the model name and number on the box, under the bar code. Cards known to work have the following:
- WinTV-NOVA-T-500 model 289 SL-289-V2.0-UK
- List incomplete, please add
WinTV-NOVA-TD-500
This card appears to have been released, in low volumes, only in the UK, but unfortunately it seems that Hauppauge is shipping the Diversity* card in regular NOVA-T-500 boxes!
This newer revision can be distinguished by:
On the box:
- You will find the model name and number under the bar code:
- WinTV-NOVA-T-500 model 289 SL-289-V2.1-UK.
- (List incomplete, please add)
- The box also has a sticker stating it is the diversity option and only suitable for intel cards.
- To quote one user running the device under Windows: "When i put it in my athlon based XP box it blue screened as soon as i tried to load the drivers. I brought mine from Amazon.co.uk and there was no mention that this card was any different or wouldn't work with non-intel processors."
On the card:
- it is labeled with the 'Diversity' feature stickers and the actual model number on the printed circuit board is NOVA-TD-500 (WinTV-NOVA-TD-500 DVB-T 68109 LF rev C1B5)
- the card has two aerial connectors.
- it uses a DiB0710 host USB controller (USB-to-PCI controller) instead of a VIA controller
The DIBcom DiB0710 controller used by this newer revision was apparently never sold for mass-production and DIBcom has end-of-life'd the chip. Furthermore, DIBcom currently do not plan on providing support for this controller. Conseqeuntly, given the low shipping volume and the limited support options, development of a Linux driver for this revision would likely be a waste of effort. [1][2]
Making it work
Firmware
You will need the dvb-usb-dib0700-03-pre1.fw firmware file in
/lib/firmware
or the relevant place for your distribution.
Drivers
Status on August 2, 2007
Thanks for work by Patrick Boettcher, Olivier Danet, Janne Grunau, Jose Alberto Reguero and probably others.
All fixes have been merged into the current tree.
Just use Mercurial by following the How_to_install_DVB_device_drivers instructions.
* MT1060_IF1_freq_set.diff - 2.3K
* Sets the MT2060 IF1 frequency according to the calibration values stored in the EEPROM. It is supposed to enhance the signal quality
* Olivier Danet
* Post: http://linuxtv.org/pipermail/linux-dvb/2006-December/014926.html
Please report on the list.
On-board amplifier
You may want/need to turn on the on-board amplifier:
sudo gedit /etc/modprobe.d/options
Add:
options dvb-usb-dib0700 force_lna_activation=1
Sample kernel output
[ 30.965645] dib0700: loaded with support for 5 different device-types [ 30.965925] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 31.008899] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-03-pre1.fw' [ 31.206081] dib0700: firmware started successfully. [ 31.711176] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state. [ 31.711222] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 31.711325] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T) [ 31.831535] DVB: registering frontend 0 (DiBcom 3000MC/P)... [ 31.854890] MT2060: successfully identified (IF1 = 1220) [ 32.388673] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 32.388853] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T) [ 32.394293] DVB: registering frontend 1 (DiBcom 3000MC/P)... [ 32.398790] MT2060: successfully identified (IF1 = 1220) [ 32.959607] input: IR-receiver inside an USB DVB receiver as /class/input/input4 [ 32.959633] dvb-usb: schedule remote query interval to 150 msecs. [ 32.959637] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T successfully initialized and connected. [ 32.959657] usbcore: registered new interface driver dvb_usb_dib0700
Remote control
Grey top, black bottom, 45 buttons, snowboard shape.
It gives output into
/dev/input/eventX
where X is variable and depends on your system.
LIRC will use it without needing a special kernel module. use the following driver:
dev/input
Here is a proper lircd.conf file:
#
# brand: Hauppauge NOVA-T-500
# model no. of remote control: Hauppage Nova-T-500 Snowboard Shape Silver over Black
#
begin remote
name NOVA-T500
bits 16
eps 30
aeps 100
one 0 0
zero 0 0
pre_data_bits 16
pre_data 0x1
gap 199999
toggle_bit 0
begin codes
Go 0x0162
Power 0x0074
TV 0x0179
Videos 0x0189
Music 0x0188
Pictures 0x00E2
Guide 0x016D
Radio 0x0181
ArrowUp 0x0067
ArrowLeft 0x0069
OK 0x0160
ArrowRight 0x006A
ArrowDown 0x006C
BackExit 0x009E
Menu 0x008B
VolumeUp 0x0073
VolumeDown 0x0072
PrevCh 0x016B
Mute 0x0071
ChannelUp 0x0192
ChannelDown 0x0193
Record 0x00A7
Rewind 0x00A8
SkipBack 0x0195
Play 0x00CF
Pause 0x0077
Stop 0x0080
Fwdwind 0x00D0
SkipFwd 0x0197
1 0x0002
2 0x0003
3 0x0004
4 0x0005
5 0x0006
6 0x0007
7 0x0008
8 0x0009
9 0x000A
* 0x0037
0 0x000B
# 0x0029
Red 0x018E
Green 0x018F
Yellow 0x0190
Blue 0x0191
end codes
end remote