[vdr] Re: VDR developer version 1.3.1

[Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>]

Lauri Tischler wrote:
> 
> Klaus Schmidinger wrote:
> 
> > Lauri Tischler wrote:
> >
> >>Klaus Schmidinger wrote:
> >>
> >>
> >>>Please go back to the original VDR/nit.c and insert the line
> >>>
> >>>  dsyslog("NIT: %6d %4d %4d %6d %6d", Transponder(), ts.getOriginalNetworkId(), ts.getTransportStreamId(), Frequency, SymbolRate);
> >>>
> >>>in the 'case SI::CableDeliverySystemDescriptorTag' branch, right before
> >>>
> >>>  bool found = false;
> >>
> >>I did that on dvb-t, removed the symbolrate, here is log..
> >>
> >>Jan 15 23:52:21 rascal vdr[7094]: switching to channel 1
> >>Jan 15 23:52:21 rascal vdr[7105]: transfer thread started (pid=7105, tid=98311)
> >>Jan 15 23:52:21 rascal vdr[7106]: receiver on device 1 thread started (pid=7106, tid=114696)
> >>Jan 15 23:52:23 rascal vdr[7098]: creating new channel 'YLE Teema' on T transponder 562 with id 8438-4097-209-0
> >>Jan 15 23:52:23 rascal vdr[7098]: creating new channel 'YLE FST' on T transponder 562 with id 8438-4097-81-0
> >>Jan 15 23:52:23 rascal vdr[7098]: creating new channel 'YLE TV2' on T transponder 562 with id 8438-4097-33-0
> >>Jan 15 23:52:23 rascal vdr[7098]: creating new channel 'YLE24' on T transponder 562 with id 8438-4097-193-0
> >>Jan 15 23:52:23 rascal vdr[7098]: changing pids of channel 106 from 0+0:0,0;0,0:0 to 513+129:660,0;0,0:2321
> >>Jan 15 23:52:23 rascal vdr[7098]: changing pids of channel 105 from 0+0:0,0;0,0:0 to 514+130:670,0;0,0:2321
> >>Jan 15 23:52:23 rascal vdr[7098]: changing pids of channel 107 from 0+0:0,0;0,0:0 to 515+131:680,0;0,0:2321
> >>Jan 15 23:52:24 rascal vdr[7098]: changing pids of channel 104 from 0+0:0,0;0,0:0 to 516+132:690,0;0,0:2321
> >>Jan 15 23:52:34 rascal vdr[7098]: NIT:    562 8438 4097 562000000
> >>Jan 15 23:52:34 rascal vdr[7098]: NIT:    562 8438 8193 658000000
> >>Jan 15 23:52:34 rascal vdr[7098]: NIT:    562 8438 12289 674000000
> >
> >
> > I assume you have only one DVB card, right?
> > New transponders are currently only tuned to during the EPG scan
> > (I'll yet have to add an option to trigger that).
> >
> > Please change the line
> >
> >   if (Device != cDevice::PrimaryDevice() || (cDevice::NumDevices() == 1 && Setup.EPGScanTimeout && now - lastActivity > Setup.EPGScanTimeout * 3600)) {
> >
> > in VDR/eitscan.c into
> >
> >   if (true) {
> >
> > and run VDR again. After about a minute it should start switching through
> > transponders (provided you have set the "EPG scan timeout" to something other than 0).
> >
> > Does it find other transponders now?
> 
> Nope, nothing happens, waited about 4 minutes, the log is the same
> 
> This is a testbox with NEXUS-S with no dish connected and
> NOVA-T.  Otherwise dvb-t works ok.

There was a bug in setting the source type of newly detected terrestrial
transponders. Should work now in version 1.3.2.

Klaus


-- 
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe vdr" as subject.