[linux-dvb] Re: [vdr] Re: ERROR (dvbdevice.c,533)

[Uwe Ortner <uwe.ortner@classic-net.de>]

Am Son, 2003-05-04 um 00.55 schrieb Andreas Kool:
> On Sun, May 04, 2003 at 12:27:26AM +0200, Oliver Endriss wrote:
> > Uwe Ortner wrote:
> > > Am Sam, 2003-05-03 um 23.24 schrieb Oliver Endriss:
> > > > Andreas Kool wrote:
> > > > > On Sat, May 03, 2003 at 08:28:10PM +0200, Uwe Ortner wrote:
> > > > > Could you please post a
> > > > >
> > > > >   lspci -nv | grep 0480 -A1
> > > > >
> > > > > here?
> > > >
> > > > Yesterday he posted this on the driver ml:
> > > > | 00:08.0 Class 0480: 1131:7146 (rev 01)
> > > > |         Subsystem: 110a:0000
> > > >
> > > > According to saa7146_core.c this is a full-featured
> > > > "Siemens cable card PCI rev1.5".
> > > >
> > > > | 00:09.0 Class 0480: 1131:7146 (rev 01)
> > > > |         Subsystem: 13c2:0002
> > > >
> > > > Is this a DVB-C card, too? According to saa7146_core.c this is a
> > > > full-featured "Technotrend/Hauppauge PCI rev2.1 or 2.2".
> > > >
> > > > > 00:0f.0 Class 0480: 1131:7146 (rev 01)
> > > > > 	Subsystem: 13c2:0000
> > > > > -------------------^^^^
> > > > > If you read the above, you have a Technotrend 1.3 card (like me)
> > > >
> > > > Ok, according to saa7146_core.c this is a full-featured
> > > > "Siemens/Technotrend/Hauppauge PCI rev1.3".
> > >
> > > there are 2 cards installed, Siemens + Hauppauge DVB-C
> >
> > Of course. (For troubleshooting a single-card setup might be better...)
> >
> > > > > In that case, you could simply use the DVB-cvs as of april, 29.
> > > > > 2003 (but not later!) ... works fine here!
> > > >
> > > > You can fix later drivers by adding your card id to the 'if'
> > > > statement at line 4965 (av7110.c). You can simply replace 0x1004,
> > > > which is wrong anyway (IMHO).
> > >
> > > I'will try this ...
> >
> > IIRC, your problem is the Siemens DVB-C (110a:0000). Correct?
> > This card should be supported already, as the 0x110a id is included in
> > that statement. Do you have an analog module?
> >
> > Maybe there is a switch or jumper which has to be set if you don't have
> > an analog module. (Sorry I don't have a DVB-C.)
> 
> It is *impossible* to mount the analogue module without changing one or two
> jumpers. (Well done, SNI :-)
> 
> And it is impossible to change the volume *without* a mounted analogue module,
> because the MSP34xx chip is located on the analogue module (once again,
> well done, SNI :-(
> 
> So please Uwe, do you have a mounted analogue module?
> 
> If not, forget about volume control with this card! (Or get one - maybe
> at eBay ...)
> 

I unmounted the analog module because it was mentioned some time before
it would cause error on the video output ...

Right now i plugged it in again, and analog sound works now :)
but I still do not have any sound on the scart(!)

Can we fix the Scart Sound problem also?

BTW: there are no jumpers on the card

Regards 
uwe



-- 
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.