Mailing List archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[linux-dvb] Re: KNC1/DVB-S - Errors in TS for PID...
On Mon, May 12, 2003 at 06:30:01PM +0200, Marcus Metzler wrote:
> Michael Lipka writes:
> > channels. While Pro7 and Kabel1 work perfectly,
They don't anymore, by the way. I've tuned signal strength to it's
maximum using a so-called "sat-finder" on one of the LNB's connectors
(labeled "14V 0kHz" on the switch-side), but that made things worse.
> You can get a channel list from satcodx.com and use it as dvbrc
> (e.g. http://www.satcodx2.com/_data/0192.sdx for astra).
> Try satscan in libdvb to see which transponders are found (e.g satscan
> 0192.sdx).
Did that and got around 707 channels on 53 transponder(-ids) (see
attached "statistics"). Thanks for the explanation on how to use
satscan.
Meanwhile I've repartitioned my HD and installed Win2k on /dev/hda1
(not as complicate as it sounds, as the machine is running "diskless"
with hda being an LVM for swapping and temporary data storage and so
on). I did that, as the card is runnig fine (well, it runs, with few
drop-outs) on my OW's machine which is also a 1GHz AMD (Duron versus
Athlon on mine) with exactly the same amount of memory, comparable
chipset (both VIA) under Win2k. Both computers are about 2m apart and
were plugged into the same Sat-socket using the very same cable. On
my machine I sometimes get a kind of still-image and a piece of sound
using the Win2k drivers and applications, but can't really watch TV
with it.
I've done some statistics on the output of dvbtune -z -f.. (check.sh).
I have
- an average bit error rate of 62174 (which sounds high, if 2^16
is the maximum),
- a signal strength of 47602 (~ 72%),
- an SNR of 51345 (78%).
So I'd like to know
1) Has anybody a pointer for me to an online document about how to
adjust my SAT equipment for digital receiving? (OT, I know,
sorry). LNB and switch should be ok (bought it with digital TV in
mind but had only analogue receivers)
2) Any ideas, why this d*** card works in a different PC but not in
mine? I've read something about PCI-latency and noticed, that the
card is set to 33 (see attached "lspci", 2nd last entry) which
someone considered too low last year. But I think I have an
RF-problem, right?
> The 1.1.6b is an older version of the driver with some bugs. I don't
> know when Ralph plans to post a newer version, it depends on how we
> can handle CI support.
> The frequencies for the transponder depend on the accuracy of your
> LNB. If there is a slight offset, it should be corected by the zig-zag
> scan in the driver, which may not work correctly in the old version.
I'm willing to beta-test it and don't even mind rebooting my PC once
and then ;-)
I may still be doing something very stupid. I've got all ideas of who
to actually view something with a "low-budget"-card from the
mailinglist.
I used
- ntuxzap -e
- ts2ps 0 0 </dev/dvb/adapter0/dvr0 > /video/rec"
and then
- mplayer /video/rec
to view the recorded stream (when it still worked, now /video/rec
remains an empty file).
> Marcus
Thanks again for you help
Michael
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: d4000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 11
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05)
Subsystem: Intel Corp. EtherExpress PRO/100+
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at db100000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at dc00 [size=32]
Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00:09.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at db101000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.1 Multimedia controller: Brooktree Corporation Bt878 (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at db102000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs: Unknown device 8064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at e400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--------------------------------------------------------------------
00:0b.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Philips Semiconductors: Unknown device 4f56
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at db103000 (32-bit, non-prefetchable) [size=512]
--------------------------------------------------------------------
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 Pro TF (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0018
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 0
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at d9000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
H-/L-Band:
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne 'if (/(.)-Band:([\d+-]*)/) {print "$1-Band: $2\n"}' dvbtune-astra.err | sort -u
L-Band: -1073742636
Not locked
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -MData::Dumper -ne '/(fe_timedout|not able to lock)/i && $count{$1}++; END {print Dumper(\%count)}' dvbtune-astra.err
$VAR1 = {
'Not able to lock' => '9',
'FE_TIMEDOUT' => '9'
};
Bit error rate (Peak: 62174.95)
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne '/Bit error rate: (\d+)/ && print "$1\n"' dvbtune-astra.err | ../hist/bin -b 10 -g
from: 1792
to: 65353
step: 6356.1
bins:10
4970.05 5
11326.15 3
17682.25 4
24038.35 4
30394.45 1
36750.55 4
43106.65 0
49462.75 2
55818.85 2
62174.95 14
68531.05 1
Signal Strength (Peak: ~ 46002-47602)
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne '/Signal strength: (\d+)/ && print "$1\n"' dvbtune-astra.err | ../hist/bin -b 10 -g
from: 44802
to: 52803
step: 800.1
bins:10
45202.05 2
46002.15 8
46802.25 7
47602.35 9
48402.45 6
49202.55 3
50002.65 1
50802.75 2
51602.85 0
52402.95 1
53203.05 1
Signal noise ratio (Peak: ~ 50216-52475)
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne '/SNR: (\d+)/ && print "$1\n"' dvbtune-astra.err | ../hist/bin -b 10 -g
from: 46263
to: 57558
step: 1129.5
bins:10
46827.75 3
47957.25 2
49086.75 5
50216.25 8
51345.75 9
52475.25 9
53604.75 2
54734.25 0
55863.75 1
56993.25 0
58122.75 1
SRate (?!)
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne '/Srate=(\d+)/ && print "$1\n"' dvbtune-astra.err | ../hist/bin -b 10 -g
from: 22000000
to: 27500000
step: 550000
bins:10
22275000 13
22825000 0
23375000 0
23925000 0
24475000 0
25025000 0
25575000 0
26125000 0
26675000 0
27225000 0
27775000 36
Polarisation (H=1.25, V=2.25)
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne '/Pol:(H|V)/ && print $1 eq 'H' ? 1 : 2,"\n"' dvbtune-astra.err | ../hist/bin -b 2 -g
from: 1
to: 2
step: 0.5
bins:2
1.25 25
1.75 0
2.25 24
22kHz: all off
--------------------------------------------------------------------
diskless-master:~/src/perl/stochastik/DVB$ perl -ne '/22kHz=(off|.*)/ && print $1 eq 'off' ? 0 : 2,"\n"' dvbtune-astra.err | ../hist/bin -b 2 -g
from: 0
to: 0
step: 0
Illegal division by zero at ../hist/bin line 95, <> line 49.
diskless-master:~/src/perl/stochastik/DVB$
Transponders: (53)
--------------------------------------------------------------------
TRANSPONDER ID 0001 SATID 0192 TYPE 0 FREQ 10833000 POL H SRATE 22000000 FEC 5/6
TRANSPONDER ID 0002 SATID 0192 TYPE 0 FREQ 10875000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0003 SATID 0192 TYPE 0 FREQ 11036000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0004 SATID 0192 TYPE 0 FREQ 11155000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0005 SATID 0192 TYPE 0 FREQ 11316000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0006 SATID 0192 TYPE 0 FREQ 11434000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0007 SATID 0192 TYPE 0 FREQ 11477000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0008 SATID 0192 TYPE 0 FREQ 11538000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0009 SATID 0192 TYPE 0 FREQ 11568000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 000a SATID 0192 TYPE 0 FREQ 11596000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 000b SATID 0192 TYPE 0 FREQ 11686000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 000c SATID 0192 TYPE 0 FREQ 11720000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 000d SATID 0192 TYPE 0 FREQ 11739000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 000e SATID 0192 TYPE 0 FREQ 11758000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 000f SATID 0192 TYPE 0 FREQ 11778000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0010 SATID 0192 TYPE 0 FREQ 11798000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0011 SATID 0192 TYPE 0 FREQ 11817000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0012 SATID 0192 TYPE 0 FREQ 11837000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0013 SATID 0192 TYPE 0 FREQ 11856000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0014 SATID 0192 TYPE 0 FREQ 11895000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0015 SATID 0192 TYPE 0 FREQ 11934000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0016 SATID 0192 TYPE 0 FREQ 11954000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0017 SATID 0192 TYPE 0 FREQ 11992000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0018 SATID 0192 TYPE 0 FREQ 12012000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0019 SATID 0192 TYPE 0 FREQ 12032000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 001a SATID 0192 TYPE 0 FREQ 12051000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 001b SATID 0192 TYPE 0 FREQ 12070000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 001c SATID 0192 TYPE 0 FREQ 12109000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 001d SATID 0192 TYPE 0 FREQ 12129000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 001e SATID 0192 TYPE 0 FREQ 12148000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 001f SATID 0192 TYPE 0 FREQ 12188000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0020 SATID 0192 TYPE 0 FREQ 12207000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0021 SATID 0192 TYPE 0 FREQ 12226000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0022 SATID 0192 TYPE 0 FREQ 12285000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0023 SATID 0192 TYPE 0 FREQ 12304000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0024 SATID 0192 TYPE 0 FREQ 12324000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0025 SATID 0192 TYPE 0 FREQ 12344000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0026 SATID 0192 TYPE 0 FREQ 12363000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0027 SATID 0192 TYPE 0 FREQ 12382000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 0028 SATID 0192 TYPE 0 FREQ 12402000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 0029 SATID 0192 TYPE 0 FREQ 12460000 POL H SRATE 27500000 FEC 3/4
TRANSPONDER ID 002a SATID 0192 TYPE 0 FREQ 12480000 POL V SRATE 27500000 FEC 3/4
TRANSPONDER ID 002b SATID 0192 TYPE 0 FREQ 12515000 POL H SRATE 22000000 FEC 5/6
TRANSPONDER ID 002c SATID 0192 TYPE 0 FREQ 12544000 POL H SRATE 22000000 FEC 5/6
TRANSPONDER ID 002d SATID 0192 TYPE 0 FREQ 12552000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 002e SATID 0192 TYPE 0 FREQ 12574000 POL H SRATE 22000000 FEC 5/6
TRANSPONDER ID 002f SATID 0192 TYPE 0 FREQ 12582000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0030 SATID 0192 TYPE 0 FREQ 12610000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0031 SATID 0192 TYPE 0 FREQ 12633000 POL H SRATE 22000000 FEC 5/6
TRANSPONDER ID 0032 SATID 0192 TYPE 0 FREQ 12640000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0033 SATID 0192 TYPE 0 FREQ 12663000 POL H SRATE 22000000 FEC 5/6
TRANSPONDER ID 0034 SATID 0192 TYPE 0 FREQ 12670000 POL V SRATE 22000000 FEC 5/6
TRANSPONDER ID 0035 SATID 0192 TYPE 0 FREQ 12692000 POL H SRATE 22000000 FEC 5/6
Channels per transponder:
--------------------------------------------------------------------
perl -ne '/TRANSPONDER ID\s+(\S+)/ && do {$trans=$1}; /CHANNEL ID/ && $count{$trans}++; END {foreach(sort(keys(%count))) {print "Channels on transponder $_: $count{$_}\n"}}'
Channels on transponder 0001: 7
Channels on transponder 0002: 9
Channels on transponder 0003: 9
Channels on transponder 0004: 17
Channels on transponder 0005: 8
Channels on transponder 0006: 14
Channels on transponder 0007: 11
Channels on transponder 0008: 9
Channels on transponder 0009: 11
Channels on transponder 000a: 2
Channels on transponder 000b: 11
Channels on transponder 000c: 7
Channels on transponder 000d: 15
Channels on transponder 000e: 12
Channels on transponder 000f: 9
Channels on transponder 0010: 20
Channels on transponder 0011: 12
Channels on transponder 0012: 20
Channels on transponder 0013: 12
Channels on transponder 0014: 13
Channels on transponder 0015: 10
Channels on transponder 0016: 12
Channels on transponder 0017: 9
Channels on transponder 0018: 15
Channels on transponder 0019: 15
Channels on transponder 001a: 52
Channels on transponder 001c: 26
Channels on transponder 001d: 13
Channels on transponder 001e: 20
Channels on transponder 001f: 6
Channels on transponder 0020: 22
Channels on transponder 0021: 4
Channels on transponder 0022: 14
Channels on transponder 0023: 13
Channels on transponder 0024: 15
Channels on transponder 0025: 12
Channels on transponder 0026: 57
Channels on transponder 0027: 10
Channels on transponder 0028: 10
Channels on transponder 0029: 2
Channels on transponder 002a: 8
Channels on transponder 002b: 11
Channels on transponder 002c: 2
Channels on transponder 002d: 14
Channels on transponder 002e: 23
Channels on transponder 002f: 9
Channels on transponder 0030: 10
Channels on transponder 0031: 6
Channels on transponder 0032: 10
Channels on transponder 0033: 2
Channels on transponder 0034: 19
Channels on transponder 0035: 28
Home |
Main Index |
Thread Index