Hauppauge WinTV-HVR-4000: Difference between revisions
Jump to navigation
Jump to search
| Line 123: | Line 123: | ||
{{Note|As above, the latest diff for Multifrontend is against a version of V4L that is not the latest. You will need to use: hg clone -r 1abbd650fe07 http://linuxtv.org/hg/v4l-dvb --[[User:Comm|Comm]] 14:06, 20 May 2008 (BST)}} |
{{Note|As above, the latest diff for Multifrontend is against a version of V4L that is not the latest. You will need to use: hg clone -r 1abbd650fe07 http://linuxtv.org/hg/v4l-dvb --[[User:Comm|Comm]] 14:06, 20 May 2008 (BST)}} |
||
Kaffeine handles multiple frontends well without modification -- they appear in the DVB settings as "DVB Device 0:0" (=/dev/dvb/adapter0/frontend0, i.e. DVB- |
[[Kaffeine]] handles multiple frontends well without modification -- they appear in the DVB settings as "DVB Device 0:0" (=/dev/dvb/adapter0/frontend0, i.e. DVB-S) and "DVB Device 0:1" (=/dev/dvb/adapter0/frontend1, i.e. DVB-T). Both devices can be configured and tuned in the application, and Kaffeine will switch to the correct one each time |
||
you change the channel. DiSEqC 1.2 is supported too. |
you change the channel. DiSEqC 1.2 is supported too. |
||
Most programs such as mythtv don't know about multi frontends yet. You can only use 1 at a time, but this allows you to swap between them without having to load the modules in differently. |
Most programs such as [[mythtv]] don't know about multi frontends yet. You can only use 1 at a time, but this allows you to swap between them without having to load the modules in differently. |
||
<pre> |
<pre> |
||
Revision as of 16:27, 24 August 2008
A hybrid DVB-S2 PCI card from Hauppauge.
It is currently not supported under Linux. However, experimental support for some of the device's features is available (see below for details).
Overview/Features
Features DVB-S2, DVB-S, DVB-T, Analog TV, Composite, and FM Radio (not supported yet) all in one card!
Note: DVB-T and DVB-S cannot be used at the same, but you can use 1 if not using the other.
Components Used
- Conexant CX24116 (demodulator)
- Conexant CX24118A (demodulator)
- Conexant CX23880 (A/V decoder & PCI bridge)
Identification
04:08.0 0400: 14f1:8800 (rev 05)
Subsystem: 0070:6902
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:08.1 0480: 14f1:8811 (rev 05)
Subsystem: 0070:6902
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:08.2 0480: 14f1:8802 (rev 05)
Subsystem: 0070:6902
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:08.4 0480: 14f1:8804 (rev 05)
Subsystem: 0070:6902
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1500ns min, 63750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 255
Region 0: Memory at f7000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Making it Work
Firmware
One could use the script provided from wget-fw.sh to fetch the firmware for us. Basically what it does is :
1) fetch an archive : "wget ftp://167.206.143.11/outgoing/Oxford/88x_2_119_25023_WHQL.zip"
2) decompress what's needed : "unzip -jo 88x_2_119_25023_WHQL.zip Driver88/hcw88bda.sys"
3) put the firmware at the right place : "dd if=hcw88bda.sys of=/lib/firmware/dvb-fe-cx24116.fw skip=81768 bs=1 count=32522"
Debian: Place file in /usr/lib/hotplug/firmware/
For slightly newer firmware using drivers from Hauppauge
1) Download the driver archive : "wget http://www.wintvcd.co.uk/drivers/88x_2_122_26109_WHQL.zip"
2) Decompress the .sys file : "unzip -jo 88x_2_122_26109_WHQL.zip Driver88/hcw88bda.sys"
3) Extract the firmware at the right place : "dd if=hcw88bda.sys of=dvb-fe-cx24116.fw skip=75504 bs=1 count=32501"
4) Copy the firmware file (dvb-fe-cx24116.fw) to the appropriate place (typically /lib/firmware)
Drivers
There are currently no in kernel drivers for this card.
Note: If someone wants to provide a brief synopsis of the driver tale of woe, outlining why there isn't a greater level of support, then do so here ... or just read here
However, experimental support does exist.
This allows DVB-T or DVB-S support:
hg clone http://linuxtv.org/hg/v4l-dvb wget http://dev.kewl.org/hauppauge/v4l-dvb-hg-sfe-latest.diff patch -d v4l-dvb -p1 < v4l-dvb-hg-sfe-latest.diff cd v4l-dvb && make && make install && reboot
Note: The last revision I know of that the patches apply cleanly to is 127f67dea087, so you'll probably have to check the repository out this way: hg clone -r 127f67dea087 http://linuxtv.org/hg/v4l-dvb --Growlizing 13:10, 10 April 2008 (CEST)
- This didn't work for me with Mercurial 0.9.1: I got the message "abort: clone by revision not supported yet for remote repositories". Uninstalling the distribution version, then downloading and make install-ing 1.0.2 fixed it. Doesn't build against Linux 2.6.26.2, though. Bloop 20:18, 20 August 2008 (CEST)
See: http://dev.kewl.org/hauppauge/ about enabling DVB-T or DVB-S2 (DVB-S is the default at the moment)
Multifrontend driver
These drivers give you the ability to have multi frontend on the HVR4000. (ie DVB-T and DVB-S tuners )
See: http://dev.kewl.org/hauppauge/
hg clone http://linuxtv.org/hg/v4l-dvb wget http://dev.kewl.org/hauppauge/v4l-dvb-hg-mfe-latest.diff patch -d v4l-dvb -p1 < v4l-dvb-hg-mfe-latest.diff cd v4l-dvb && make && make install && reboot
Note: As above, the latest diff for Multifrontend is against a version of V4L that is not the latest. You will need to use: hg clone -r 1abbd650fe07 http://linuxtv.org/hg/v4l-dvb --Comm 14:06, 20 May 2008 (BST)
Kaffeine handles multiple frontends well without modification -- they appear in the DVB settings as "DVB Device 0:0" (=/dev/dvb/adapter0/frontend0, i.e. DVB-S) and "DVB Device 0:1" (=/dev/dvb/adapter0/frontend1, i.e. DVB-T). Both devices can be configured and tuned in the application, and Kaffeine will switch to the correct one each time you change the channel. DiSEqC 1.2 is supported too.
Most programs such as mythtv don't know about multi frontends yet. You can only use 1 at a time, but this allows you to swap between them without having to load the modules in differently.
mkdir /dev/dvb/adapter1 ln -s /dev/dvb/adapter0/frontend1 /dev/dvb/adapter1/frontend0 ln -s /dev/dvb/adapter0/net1 /dev/dvb/adapter1/net0 ln -s /dev/dvb/adapter0/dvr1 /dev/dvb/adapter1/dvr0 ln -s /dev/dvb/adapter0/demux1 /dev/dvb/adapter1/demux0
Multiproto driver
The wiki in german languagedescribes what has to be done in order to compile "standard" multiproto driver.
Unfortunately at the date of writing, there is no support for our beloved card, so one should fetch
the patch from linuxtv mailing list which you should apply to the tree before compiling the driver. I haven't tested the patch which adds the multi frontend support but it's certainly a way to follow :-)
After having applied the patch, one could follow the first link of this section to have a VDR with full DVB-S2 support!!!
Latest - 29-1-08 --------------------------- hg clone http://jusst.de/hg/multiproto wget http://www.linuxtv.org/pipermail/linux-dvb/attachments/20080128/adee4c88/attachment-0001.bin mv attachment-0001.bin multiproto-hvr4k-2008-01-28.patch.bz2 bunzip2 multiproto-hvr4k-2008-01-28.patch.bz2 ln -s multiproto a; ln -s multiproto b patch -p0 < multiproto-hvr4k-2008-01-28.patch cd multiproto run make menuconfig and disable the USB capture cards as the em88 drivers are broken and make sure customise frontends is enabled. make && make install && reboot
UPDATE 1st Aug 2008: Igor Liplianin has created another repository containing multiproto code and szap2 at http://liplianindvb.sourceforge.net/hg/, reported to be working with the HVR-4000. See http://www.linuxtv.org/pipermail/linux-dvb/2008-July/027514.html. This appears to be similar to the V4L/DVB staging development repository at http://linuxtv.org/hg/v4l-dvb/ but with the addition of multiproto code.
hg clone http://liplianindvb.sourceforge.net/hg/liplianindvb hg clone http://liplianindvb.sourceforge.net/hg/szap2
Sample kernel output
When Enabled for DVB-S (options cx88-dvb frontend=0) (Kernel 2.6.23.14) ----------------------------------------------------------------------- cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded cx88/0: cx2388x v4l2 driver version 0.0.6 loaded cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59,autodetected] cx88[0]: TV tuner type 63, Radio tuner type -1 cx2388x alsa driver version 0.0.6 loaded cx88[0]: i2c init: enabling analog demod on HVR1300/3000/4000 tuner tveeprom 2-0050: Hauppauge model 69009, rev B2D3, serial# 2807241 tveeprom 2-0050: MAC address is 00-0D-FE-2A-D5-C9 tveeprom 2-0050: tuner model is Philips FMD1216MEX (idx 133, type 63) tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 2-0050: audio processor is CX882 (idx 33) tveeprom 2-0050: decoder processor is CX882 (idx 25) tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69009 input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input3 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/2: found at 0000:04:08.2, rev: 5, irq: 21, latency: 32, mmio: 0xf8000000 cx88[0]/0: found at 0000:04:08.0, rev: 5, irq: 21, latency: 32, mmio: 0xfa000000 cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59] cx88[0]/2: cx2388x based DVB/ATSC card tuner' 2-0043: chip found @ 0x86 (cx88[0]) tda9887 2-0043: tda988[5/6/7] found tuner' 2-0061: chip found @ 0xc2 (cx88[0]) tuner-simple 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) tuner' 2-0063: chip found @ 0xc6 (cx88[0]) cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 cx88[0]/0: registered device radio0 DVB: registering new adapter (cx88[0]) DVB: registering frontend 0 (Conexant CX24116/CX24118)... cx88[0]/1: CX88x/0: ALSA support for cx2388x boards cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)... cx24116_firmware_ondemand: Waiting for firmware upload(2)... cx24116_load_firmware: FW version 1.20.79.0 cx24116_firmware_ondemand: Firmware upload complete When enabled for DVB-T (options cx88-dvb frontend=1) (Kernel 2.6.23.14) ----------------------------------------------------------------------- cx88/0: cx2388x v4l2 driver version 0.0.6 loaded cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59,autodetected] cx88[0]: TV tuner type 63, Radio tuner type -1 cx2388x alsa driver version 0.0.6 loaded cx88[0]: i2c init: enabling analog demod on HVR1300/3000/4000 tuner tveeprom 2-0050: Hauppauge model 69009, rev B2D3, serial# 2807241 tveeprom 2-0050: MAC address is 00-0D-FE-2A-D5-C9 tveeprom 2-0050: tuner model is Philips FMD1216MEX (idx 133, type 63) tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 2-0050: audio processor is CX882 (idx 33) tveeprom 2-0050: decoder processor is CX882 (idx 25) tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69009 input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input3 cx88[0]/0: found at 0000:04:08.0, rev: 5, irq: 20, latency: 32, mmio: 0xfa000000 tuner' 2-0043: chip found @ 0x86 (cx88[0]) tda9887 2-0043: tda988[5/6/7] found tuner' 2-0061: chip found @ 0xc2 (cx88[0]) tuner-simple 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) tuner' 2-0063: chip found @ 0xc6 (cx88[0]) cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 cx88[0]/0: registered device radio0 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/1: CX88x/0: ALSA support for cx2388x boards cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59] cx88[0]/2: cx2388x based DVB/ATSC card DVB: registering new adapter (cx88[0]) DVB: registering frontend 0 (Conexant CX22702 DVB-T)... When Enabled for DVB-S/S2 multiproto (options cx88-dvb frontend=0) (Kernel 2.6.23.1) ------------------------------------------------------------------------------------ cx2388x v4l2 driver version 0.0.6 loaded CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=58,autodetected] TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded cx88[0]: i2c init: enabling analog demod on HVR1300/3000/4000 tuner tveeprom 2-0050: Hauppauge model 69009, rev B2D3, serial# 2807241 tveeprom 2-0050: MAC address is 00-0D-FE-2A-D5-C9 tveeprom 2-0050: tuner model is Philips FMD1216MEX (idx 133, type 63) tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 2-0050: audio processor is CX882 (idx 33) tveeprom 2-0050: decoder processor is CX882 (idx 25) tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69009 input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input3 cx88[0]/0: found at 0000:04:08.0, rev: 5, irq: 20, latency: 32, mmio: 0xfa000000 cx2388x alsa driver version 0.0.6 loaded tuner 2-0043: chip found @ 0x86 (cx88[0]) tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 2-0061: chip found @ 0xc2 (cx88[0]) tuner 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) tuner 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) tuner 2-0063: chip found @ 0xc6 (cx88[0]) cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 cx88[0]/0: registered device radio0 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/2: found at 0000:04:08.2, rev: 5, irq: 20, latency: 32, mmio: 0xf8000000 cx2388x dvb driver version 0.0.6 loaded cx8802_register_driver() ->registering driver type=dvb access=shared CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=58] cx88[0]/2: cx2388x based dvb card ACPI: PCI Interrupt 0000:04:08.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 20 cx88[0]/1: CX88x/0: ALSA support for cx2388x boards DVB: registering new adapter (cx88[0]) DVB: registering frontend 0 (Conexant CX24116/CX24118)... cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)... cx24116_firmware_ondemand: Waiting for firmware upload(2)... cx24116_firmware_ondemand: Firmware upload complete Multi Frontend Drivers (kernel 2.6.24) -------------------------------------- cx88/0: cx2388x v4l2 driver version 0.0.6 loaded cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59,autodetected], frontend(s): 2 cx88[0]: TV tuner type 63, Radio tuner type -1 cx2388x alsa driver version 0.0.6 loaded cx88[0]: i2c init: enabling analog demod on HVR1300/3000/4000 tuner tveeprom 2-0050: Hauppauge model 69009, rev B2D3, serial# 2807241 tveeprom 2-0050: MAC address is 00-0D-FE-2A-D5-C9 tveeprom 2-0050: tuner model is Philips FMD1216MEX (idx 133, type 63) tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 2-0050: audio processor is CX882 (idx 33) tveeprom 2-0050: decoder processor is CX882 (idx 25) tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69009 input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input3 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/2: found at 0000:04:08.2, rev: 5, irq: 21, latency: 32, mmio: 0xf8000000 cx8802_probe() allocating 2 frontend(s) cx88[0]/0: found at 0000:04:08.0, rev: 5, irq: 21, latency: 32, mmio: 0xfa000000 cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59] cx88[0]/2: cx2388x based DVB/ATSC card tuner' 2-0043: chip found @ 0x86 (cx88[0]) tda9887 2-0043: tda988[5/6/7] found tuner' 2-0061: chip found @ 0xc2 (cx88[0]) tuner-simple 2-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) tuner' 2-0063: chip found @ 0xc6 (cx88[0]) cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 cx88[0]/0: registered device radio0 cx88[0]/1: CX88x/0: ALSA support for cx2388x boards tda9887 2-0043: i2c i/o error: rc == -121 (should be 4) DVB: registering new adapter (cx88[0]) DVB: registering adapter 0 frontend 0 (Conexant CX24116/CX24118)... DVB: registering adapter 0 frontend 1 (Conexant CX22702 DVB-T)... cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)... cx24116_firmware_ondemand: Waiting for firmware upload(2)... cx24116_load_firmware: FW version 1.20.79.0 cx24116_firmware_ondemand: Firmware upload complete
Sound driver
Alsa driver: cx88_alsa.
To make sure the sound card in the HVR-4000 does not grab card index 0 (instead of your motherboard or discrete sound card) add the following to /etc/modprobe.d/alsa-base (or wherever your distro sets alsa kernel module options):
# Prevent abnormal drivers from grabbing index 0 options cx88_alsa index=-2
Remote Control Support
When you have installed the drivers check dmesg/logs and you'll find a line like:
input: CX88 IR (Hauppauge WinTV-HVR4000 as /class/input/inputX
You can run lirc for example like: lircd --driver=dev/input --device=/dev/input/eventX (replace X with what it finds in the dmesg)
Debian: edit /etc/lirc/hardware.conf DRIVER="dev/input" DEVICE="/dev/input/eventX"
/etc/lirc/lircd.conf (Works)
begin remote
name Hauppauge-HVR4000-Remote
bits 16
eps 30
aeps 100
one 0 0
zero 0 0
pre_data_bits 16
pre_data 0x8001
gap 133325
toggle_bit_mask 0x8001001C
begin codes
Power 0x0074
Go 0x0161
TV 0x0179
Video 0x0189
Music 0x0188
Pictures 0x016F
Guide 0x016D
Radio 0x0181
Up 0x0067
Down 0x006C
Left 0x0069
Right 0x006A
OK 0x001C
Back/Exit 0x00AE
Menu 0x008B
PrevCh 0x019C
Mute 0x0071
Vol+ 0x0073
Vol- 0x0072
Ch+ 0x0192
Ch- 0x0193
Rec 0x00A7
Stop 0x0080
Play 0x00CF
Pause 0x0077
Rewind 0x00A8
Forward 0x00D0
Replay 0x00A5
Skip 0x00A3
1 0x0002
2 0x0003
3 0x0004
4 0x0005
5 0x0006
6 0x0007
7 0x0008
8 0x0009
9 0x000A
0 0x000B
Text 0x0184
Sub/CC 0x0172
Red 0x018E
Green 0x018F
Yellow 0x0190
Blue 0x0191
end codes
end remote