I recently obtained a EMP-Centauri S170-CP-16 switch that does 16in by 16out. I attached the two LNC of each LNB to the switch. So the way it should work according the docs is:
LNC 1-4 are Diseqc port 0 LNC 5-8 are Diseqc port 1 LNC 9-12 are Diseqc port 2 LNC 12-16 are Diseqc port 3
The switch automatically sends 13v and 18v alternating on the LNC to the LNBs. Finally I need to use Tone to switch between the two LNBs on any Diseqc port.
LNB 1 - Diseqc 0 and no tone LNB 2 - Diseqc 0 and 22mhz tone LNB 3 - Diseqc 1 and no tone LNB 4 - Diseqc 1 and 22mhz tone LNB 5 - Diseqc 2 and no tone LNB 6 - Diseqc 2 and 22mhz tone LNB 7 - Diseqc 3 and no tone LNB 8 - Diseqc 3 and 22mhz tone
I use 5 legacy circular LNB and one Universal linear LNB. I tried many variations of diseqc.conf without luck. Did anyone have any luck getting VDR to control such a switch? Or can someone suggest a syntax for the Diseqc commands
Thanks
-----Original Message----- From: vdr-bounces@linuxtv.org [mailto:vdr-bounces@linuxtv.org] On Behalf Of Gregoire Favre Sent: Monday, January 29, 2007 6:44 PM To: VDR Mailing List Subject: Re: [vdr] Safer diseqc setup ?
On Mon, Jan 29, 2007 at 10:04:53PM +0000, Ilariu Raducan wrote:
I found some settings that work:
Lucky you, one of my test diseqc.conf is :
S19.2E 11700 V 9750 t v W15 [E0 10 38 03] W100 [E0 10 38 F0] W100 [E1 10 38 F0] W100 [E0 11 00] W100 A W15 t S19.2E 99999 V 10600 t v W15 [E0 10 38 03] W100 [E0 10 38 F1] W100 [E1 10 38 F1] W100 [E0 11 00] W100 A W15 T S19.2E 11700 H 9750 t V W15 [E0 10 38 03] W100 [E0 10 38 F2] W100 [E1 10 38 F2] W100 [E0 11 00] W100 A W15 t S19.2E 99999 H 10600 t V W15 [E0 10 38 03] W100 [E0 10 38 F3] W100 [E1 10 38 F3] W100 [E0 11 00] W100 A W15 T S13.0E 11700 V 9750 t v W15 [E0 10 38 03] W100 [E0 10 38 F4] W100 [E1 10 38 F4] W100 [E0 11 00] W100 B W15 t S13.0E 99999 V 10600 t v W15 [E0 10 38 03] W100 [E0 10 38 F5] W100 [E1 10 38 F5] W100 [E0 11 00] W100 B W15 T S13.0E 11700 H 9750 t V W15 [E0 10 38 03] W100 [E0 10 38 F6] W100 [E1 10 38 F6] W100 [E0 11 00] W100 B W15 t S13.0E 99999 H 10600 t V W15 [E0 10 38 03] W100 [E0 10 38 F7] W100 [E1 10 38 F7] W100 [E0 11 00] W100 B W15 T S28.2E 11700 V 9750 t v W15 [E0 10 38 03] W100 [E0 10 38 F8] W100 [E1 10 38 F8] W100 [E0 11 00] W100 A W15 t S28.2E 99999 V 10600 t v W15 [E0 10 38 03] W100 [E0 10 38 F9] W100 [E1 10 38 F9] W100 [E0 11 00] W100 A W15 T S28.2E 11700 H 9750 t V W15 [E0 10 38 03] W100 [E0 10 38 FA] W100 [E1 10 38 FA] W100 [E0 11 00] W100 A W15 t S28.2E 99999 H 10600 t V W15 [E0 10 38 03] W100 [E0 10 38 FB] W100 [E1 10 38 FB] W100 [E0 11 00] W100 A W15 T
which is pretty close to yours, it works well for ONE card, but for example if I start to reccord SSR-Espace 2;Radio Suisse Romande:12382:hC34:S19.2E:27500:0:218:0:0:928:318:8500:0
I then can only tune to Hotbird... if I stop the reccording, no change, still only Hotbird.
Thank for your email, and happy VDR :-)