Hi!
I got a problem while receiving TF1 (TPS France). I can tune to this channel, and then view the channels for about 20 seconds, but after that the stream stops, the screen is somehow distorted, if I switch again to TF1 I get the message "No right to watch" and the channel is never shown until I do a CAM reset.
My Viaccess CAM has firmware version 1.07, and I tried to update the firmware to 1.08, I tried vdr-1.3.38 and 1.4.2, but after the message "Please do not extract ..." no further messages are shown, in the manual for updating the CAM they tell that the update should need 30 minutes, I had this channel tuned about 2 days and nothing happed. No progress messages, and no update. After reinserting the CAM the firmware version is still 1.0.7.
Can anybody tell me what to do, to get TF1 working again?
Regards
Marco
Hi!
Has nobody a glue on this!
Regards
Marco
Marco Goebenich schrieb:
Hi!
I got a problem while receiving TF1 (TPS France). I can tune to this channel, and then view the channels for about 20 seconds, but after that the stream stops, the screen is somehow distorted, if I switch again to TF1 I get the message "No right to watch" and the channel is never shown until I do a CAM reset.
My Viaccess CAM has firmware version 1.07, and I tried to update the firmware to 1.08, I tried vdr-1.3.38 and 1.4.2, but after the message "Please do not extract ..." no further messages are shown, in the manual for updating the CAM they tell that the update should need 30 minutes, I had this channel tuned about 2 days and nothing happed. No progress messages, and no update. After reinserting the CAM the firmware version is still 1.0.7.
Can anybody tell me what to do, to get TF1 working again?
Regards
Marco
On Mon, Sep 04, 2006 at 11:47:15AM +0200, Marco Göbenich wrote:
Has nobody a glue on this!
Take your CAM, put it on an official TPS receiver, tune on it to the specified transponder, wait... and take your CAM back to your VDR box...
I haven't tested it, but I am quiete certain it should work :-)
Hi!
This would not work while my original TPS receiver has only a slot for the smartcard, not for a CAM.
Has nobody else problems to receive TF1?
Am I the first person who tries to update CAM firmware with VDR?
Regards
Marco
Gregoire Favre schrieb:
On Mon, Sep 04, 2006 at 11:47:15AM +0200, Marco Göbenich wrote:
Has nobody a glue on this!
Take your CAM, put it on an official TPS receiver, tune on it to the specified transponder, wait... and take your CAM back to your VDR box...
I haven't tested it, but I am quiete certain it should work :-)
Marco Goebenich mg@vierzehn.com writes:
I got a problem while receiving TF1 (TPS France). I can tune to this channel, and then view the channels for about 20 seconds, but after that the stream stops, the screen is somehow distorted, if I switch again to TF1 I get the message "No right to watch" and the channel is never shown until I do a CAM reset.
My Viaccess CAM has firmware version 1.07, and I tried to update the firmware to 1.08, I tried vdr-1.3.38 and 1.4.2, but after the message
What CAM brand ? What card are you using ?
Anyway, from my experience with my Nova-CI, I couldn't update my SCM card with vdr. From what I figured out of budget-ci driver, the update as described by SCM could not work (the driver sends a reset to the CAM at the beginning of the update procedure.)
I finally sold my SCM CAM and bought an Aston. I has no problem ever since.
The other possibility is to update your CAM in a regular sat receiver with a PCMCIA slot.
HTH
-
Dominique Dumont -
Gregoire Favre -
Marco Goebenich -
Marco Göbenich