Hi,
after some time I've improved the gotox patch for vdr - it is now correctly resolving condition for sending diseqc command in cDvbTuner::SetFrontend(void) even if diseqc command doesn't change also with cascaded diseqc switches. So the diseqc is now sent immediately after channel switch and not after frontend tuning is timeouted.
It was tested with diseqc.conf entries like this (cascaded: motor <-> uncommitted switch <-> committed switch):
S1.0W 11700 V 9750 t V G [E0 10 39 F1] v W30 [E0 10 38 FC] W30 v t S1.0W 99999 V 10600 t V G [E0 10 39 F1] v W30 [E0 10 38 FD] W30 v T S1.0W 11700 H 9750 t V G [E0 10 39 F1] V W30 [E0 10 38 FE] W30 V t S1.0W 99999 H 10600 t V G [E0 10 39 F1] V W30 [E0 10 38 FF] W30 V T
S9.0E 11700 V 9750 t V G [E0 10 39 F1] v W30 [E0 10 38 FC] W30 v t S9.0E 99999 V 10600 t V G [E0 10 39 F1] v W30 [E0 10 38 FD] W30 v T S9.0E 11700 H 9750 t V G [E0 10 39 F1] V W30 [E0 10 38 FE] W30 V t S9.0E 99999 H 10600 t V G [E0 10 39 F1] V W30 [E0 10 38 FF] W30 V T
BR,
Ales
I can't try it atm because a relay went bad in my rotor. Only goes one direction. But looking at the patch, you put the user location in the patch, not the conf?
On 1/28/2011 7:40 AM, Ales Jurik wrote:
Hi,
after some time I've improved the gotox patch for vdr - it is now correctly resolving condition for sending diseqc command in cDvbTuner::SetFrontend(void) even if diseqc command doesn't change also with cascaded diseqc switches. So the diseqc is now sent immediately after channel switch and not after frontend tuning is timeouted.
It was tested with diseqc.conf entries like this (cascaded: motor<-> uncommitted switch<-> committed switch):
S1.0W 11700 V 9750 t V G [E0 10 39 F1] v W30 [E0 10 38 FC] W30 v t S1.0W 99999 V 10600 t V G [E0 10 39 F1] v W30 [E0 10 38 FD] W30 v T S1.0W 11700 H 9750 t V G [E0 10 39 F1] V W30 [E0 10 38 FE] W30 V t S1.0W 99999 H 10600 t V G [E0 10 39 F1] V W30 [E0 10 38 FF] W30 V T
S9.0E 11700 V 9750 t V G [E0 10 39 F1] v W30 [E0 10 38 FC] W30 v t S9.0E 99999 V 10600 t V G [E0 10 39 F1] v W30 [E0 10 38 FD] W30 v T S9.0E 11700 H 9750 t V G [E0 10 39 F1] V W30 [E0 10 38 FE] W30 V t S9.0E 99999 H 10600 t V G [E0 10 39 F1] V W30 [E0 10 38 FF] W30 V T
BR,
Ales
vdr mailing list vdr@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
On 01/28/11 20:44, Timothy D. Lenz wrote:
I can't try it atm because a relay went bad in my rotor. Only goes one direction. But looking at the patch, you put the user location in the patch, not the conf?
On 1/28/2011 7:40 AM, Ales Jurik wrote:
Hi,
after some time I've improved the gotox patch for vdr - it is now correctly resolving condition for sending diseqc command in cDvbTuner::SetFrontend(void) even if diseqc command doesn't change also with cascaded diseqc switches. So the diseqc is now sent immediately after channel switch and not after frontend tuning is timeouted.
It was tested with diseqc.conf entries like this (cascaded: motor<-> uncommitted switch<-> committed switch):
S1.0W 11700 V 9750 t V G [E0 10 39 F1] v W30 [E0 10 38 FC] W30 v t S1.0W 99999 V 10600 t V G [E0 10 39 F1] v W30 [E0 10 38 FD] W30 v T S1.0W 11700 H 9750 t V G [E0 10 39 F1] V W30 [E0 10 38 FE] W30 V t S1.0W 99999 H 10600 t V G [E0 10 39 F1] V W30 [E0 10 38 FF] W30 V T
S9.0E 11700 V 9750 t V G [E0 10 39 F1] v W30 [E0 10 38 FC] W30 v t S9.0E 99999 V 10600 t V G [E0 10 39 F1] v W30 [E0 10 38 FD] W30 v T S9.0E 11700 H 9750 t V G [E0 10 39 F1] V W30 [E0 10 38 FE] W30 V t S9.0E 99999 H 10600 t V G [E0 10 39 F1] V W30 [E0 10 38 FF] W30 V T
BR,
Ales
vdr mailing list vdr@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
vdr mailing list vdr@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
No, all parameters are in setup.conf. If you mean initial values, they are in this patch from the first version (http://www.linuxtv.org/pipermail/vdr/2008-March/016164.html). If this is a problem in next version I'll zero it :) .
You also could see that all parameters are in config file if you take a look more down in the patch in place where file menu.c is used.
BR,
Ales
pe, 2011-01-28 kello 12:44 -0700, Timothy D. Lenz kirjoitti:
I can't try it atm because a relay went bad in my rotor. Only goes one direction. But looking at the patch, you put the user location in the patch, not the conf?
There is an OSD menu setting for it (Settings -> LNB). The value in the patch is just some initial default.
Seppo