Hello,
I am getting ts continuity errors in vdr with my tt 2300. Since 3 weeks I am trying to optimize my system. Now there is the Question of signal Problems. I did not have any problems with my other telestar receiver so I did not check the signal before. Femon shows the folowing on RTL on astra 19,2. status 1f | signal ac7c | snr d6dd | ber 00001200 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac73 | snr d6dd | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac7b | snr d6f2 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac7c | snr d73a | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac7d | snr d719 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac77 | snr d6fb | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac67 | snr d6e6 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal adb8 | snr d6f8 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac74 | snr d70d | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac78 | snr d6dd | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal ac5e | snr d6e3 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
Are these values ok or not? Can someone compare these output with the same card? Thanks
On Wednesday 21 February 2007 12:33, Halim Sahin wrote:
Hello,
I have similar values (tt 2300): status 1f | signal aef8 | snr d66e | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal aef4 | snr d680 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal aefb | snr d62f | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal aef1 | snr d62f | ber 00000000 | unc 00000000 | FE_HAS_LOCK
Are you sure this is a signal problem? Are you getting these problems at all transponders? Try to check dependency of errors on bitrate of video/audio.
Hello,
HMM what do you mean? I am getting these errors on all transponders. Sometimes there are no errors for 15 minutes. Sometimes there are errors for 4 minutes etc. I read a lot of stuff in vdr-portal and tested many driver firmware combinations. The last thing was the signal but if you are right and these femon output lines are ok I have no ideas what to test now.
Again my skystar2 in my other pC works fine. The telestar receiver works fine only the tt card doesn't. Please help.
Halim
On Wednesday 21 February 2007 14:03, Halim Sahin wrote:
I meant to test as well on channel with high bitrate as german channels as well as on some channels with lower bitrate (<2Mbps, for ex. Q TV SHOP @12148H). Are you using for output some sw decoder like softdevice, xine etc. or are you using TV output from card?
On Wednesday 21 February 2007 15:36, bastlir wrote:
I have two FF cards in 2 PC's - in one is ver. 2.3 modded (== 2300) (Sempron 3100+) and in the second is equipped with ver. 2.2 (P4 3.2GHz HT). I've tested it both and got following results: It really seems to be depend on signal strength - when strength of signal is approximately about 2/3 and little less (60%) the problem appears but first at some channels (not depending bitrate but seems to be depending on GOP length) - channels with longer GOP's are distorted first. After reloading fw into ff-card the problem disappears. It seems like a problem of FW of ff-card.
Regards
-
bastlir -
Halim Sahin