I found some settings that work:
S5.0E 11700 V 9750 t v W15 [E0 10 38 F0] W100 [E0 10 38 F0] W100 [E0 11 00] W100 A W15 t S5.0E 99999 V 10600 t v W15 [E0 10 38 F1] W100 [E0 10 38 F1] W100 [E0 11 00] W100 A W15 T S5.0E 11700 H 9750 t V W15 [E0 10 38 F2] W100 [E0 10 38 F2] W100 [E0 11 00] W100 A W15 t S5.0E 99999 H 10600 t V W15 [E0 10 38 F3] W100 [E0 10 38 F3] W100 [E0 11 00] W100 A W15 T
S13.0E 11700 V 9750 t v W15 [E0 10 38 F4] W100 [E0 10 38 F4] W100 [E0 11 00] W100 B W15 t S13.0E 99999 V 10600 t v W15 [E0 10 38 F5] W100 [E0 10 38 F5] W100 [E0 11 00] W100 B W15 T S13.0E 11700 H 9750 t V W15 [E0 10 38 F6] W100 [E0 10 38 F6] W100 [E0 11 00] W100 B W15 t S13.0E 99999 H 10600 t V W15 [E0 10 38 F7] W100 [E0 10 38 F7] W100 [E0 11 00] W100 B W15 T
S16.0E 11700 V 9750 t v W15 [E0 10 38 F8] W100 [E0 10 38 F8] W100 [E0 11 00] W100 A W15 t S16.0E 99999 V 10600 t v W15 [E0 10 38 F9] W100 [E0 10 38 F9] W100 [E0 11 00] W100 A W15 T S16.0E 11700 H 9750 t V W15 [E0 10 38 FA] W100 [E0 10 38 FA] W100 [E0 11 00] W100 A W15 t S16.0E 99999 H 10600 t V W15 [E0 10 38 FB] W100 [E0 10 38 FB] W100 [E0 11 00] W100 A W15 T
S19.2E 11700 V 9750 t v W15 [E0 10 38 FC] W100 [E0 10 38 FC] W100 [E0 11 00] W100 B W15 t S19.2E 99999 V 10600 t v W15 [E0 10 38 FD] W100 [E0 10 38 FD] W100 [E0 11 00] W100 B W15 T S19.2E 11700 H 9750 t V W15 [E0 10 38 FE] W100 [E0 10 38 FE] W100 [E0 11 00] W100 B W15 t S19.2E 99999 H 10600 t V W15 [E0 10 38 FF] W100 [E0 10 38 FF] W100 [E0 11 00] W100 B W15 T
They are in the order of ports on switch. A non proved explanation is that the LNB needs 100ms to powerup until it can work.
Regards, Ilariu
On 1/29/07, Ilariu Raducan < ilariu@gmail.com> wrote:
I'm using VDR4You distribution, and I don't want to install kaffeine on it. I want to keep it small ;)
I need to check if vdr is sending something that is not suposed to. Note that vdr works for channels on LNB1 if you disable diseqc in the setup.
Ilariu
On 1/29/07, Gregoire Favre < Gregoire.Favre@gmail.com> wrote:
On Mon, Jan 29, 2007 at 01:32:16PM +0000, Ilariu Raducan wrote:
I also have problems with 4 quad LNBs on a diseqc switch (1.0 and
another
2.0) If I plug out the cable from the card and plug it back again (reset
switch
and LNBs) I can use szap to change the channels. I believe the quad LNBs have
diseqc
switch inside and at reset they are in backward compatible mode
(Tone/Voltage).
In Diseqc specifications/recommendations they recommend the diseqc LNB
should ignore responding to Tone/Voltage commands when they receive one diseqc command. Unfortunately, I did not find the proper diseqc commands for the LNBs.
I will try today a workaround to reset the LNB before sending the diseqc.conf sequence in backward compatible mode:
- switch to another LNB (hope the power will be cut for the one I need
for
the channel)
- do the sequence for current channel
t v [E0 10 38 FF] W500 (switch to LNB4 and wait 500) [E0 10 38 F0]
W100 A
W15 t (switch to LNB1, wait for power to stabilize, use back
compatible)
If I am lucky enough the switch will cut the power for the LNB1 when I switch to LNB4.
Does anybody knows the Diseqc commands for Quad LNBs??
Very stangely, under kaffeine here all runs perfectly ??? Did you also try to use your quiete similar setup under kaffeine ?
I have tried an hudge number of setup, including diseqc reset, resent of messages...
Maybe there is only two VDR user with quad lnb in the world using diseqc ? -- Grégoire FAVRE http://gregoire.favre.googlepages.com http://www.gnupg.org
vdr mailing list vdr@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr